Turkey's Largest Projector Lamp Sales Platform
TR EN

Projector Device Maintenance

Brand-independent service since 2001Free fault diagnosisOriginal lamps, 1 year warranty
0 dayPost-maintenance test
0 °CLamp operating temperature
0Brands, all models
0%Longer lamp life with clean cooling


There are more than one cooling fan in the Projector devices. These fans provide cooling of the electronic cards with a Projector lamp working at an average of 1000 degrees inside the device. Depending on the continuous operation of the fans with the device, all the dust particles in the environment where the Projector is located are collected in the device, which causes the fan of the device to become clogged, causing the lenses and cards to become dirty. Due to the fact that the fans can not fully perform the cooling process, due to overheating in the device it causes image defects due to card failures, shortening / bursting of the lamp life and pollution of the lenses through which the light passes.

For this reason, it is necessary to have took care of your devices periodically in order to use them for a long time and get a good image. As Beta Lamp Projector we make maintenance of your Projector device in every brand and model.

What do we do in Projector Maintenance?

• Electronic cards
• Power Card
• Lamb Power Card
• Projector Lamp
• Lenses and condenser
• Device cooling fans

We disassemble all of our plastic parts and separate the lenses into pieces and clean them in our special wave pool. After cleaning up your cards and plastic parts, we collect the device again and take it test for 1 day. If there is no negativity in the test results, we make the device ready for delivery within the same working day.

Our Projector Device Maintenance Video

Request a quote or ask a questionWe reply on the phone and WhatsApp during working hours.
Symptoms

6 signs your projector needs maintenance

A projector draws dust into itself; once the fans clog, heat rises and everything starts to fail in a chain. Early maintenance prevents expensive repairs.

Louder fan noise

If the unit is noisier than it used to be, the fans are clogged with dust and spinning faster.

Temperature warning

An orange/red temperature light or a "temperature" message means cooling is no longer sufficient.

Random shutdowns

A projector switching off by itself is usually the thermal protection circuit kicking in.

Spots and blurry image

Dark spots and areas that will not focus come from dust and soot on the lens and optics.

Lamps dying early

If lamps fail or burst well before their rated life, the internal temperature is too high.

Grey filters and grilles

If the intake filter and grilles are visibly dusty, the inside is in the same condition.

Scope

What we do during periodic maintenance

The projector is fully disassembled; every part is cleaned with the right method, reassembled and tested for a day.

  • Electronic boards

    Mainboard, power board and lamp power board are cleaned with special solution; heatsinks and connectors checked.

  • Cooling fans

    All fans are removed, blades and air ducts cleaned; fans with reduced speed are replaced.

  • Lenses and optics

    The optical group is disassembled and cleaned in our wave pool; prisms and mirrors are left spotless.

  • Lamp and lamp bay

    Lamp cover, bay and reflector are cleaned; lamp hours and bulb condition are reported.

  • Filters and grilles

    Air filters are cleaned or replaced; intake and exhaust grilles cleared.

  • Plastic parts

    All covers are removed and washed; broken clips and screws replaced.

  • Heat and sensor check

    Temperature sensors and thermal paths are checked, operating temperature measured.

  • 1-day test and report

    The unit is reassembled and run under load for at least 1 day; if all is well it is ready for delivery the same business day.

How often?

Recommended maintenance intervals

The interval depends on how dusty the environment is and how many hours a day the projector runs.

Home and small officeEvery 12 months

2–3 hours a day, clean environment. The filter should be cleaned monthly by the user.

School, classroom, meeting roomEvery 6 months

6–8 hours a day of heavy use, chalk and paper dust.

Café, workshop, exhibition, industryEvery 3–4 months

Environments with heavy dust, oil vapour or cigarette smoke.

How it works

Four simple steps

  1. Get in touchCall, WhatsApp or fill in the form; tell us the brand, model and the problem.
  2. DiagnosisWe identify the right lamp or the fault; diagnosis is free of charge.
  3. Quote & approvalYou receive a clear price and time estimate before any work starts.
  4. DeliveryShipping across Türkiye or pick-up in Fatih; original lamps come with 1 year warranty.
SSS

Frequently asked questions

Could not find your answer? We reply within working hours.

Disassembly, cleaning and reassembly are usually finished the same day; the unit is then tested for 1 day. We deliver within 2 business days in total.